How to Reset GE Washer: Troubleshooting Techniques Explored
How to Reset GE Washer?
To reset a GE washer, first, shut off the circuit breaker or unplug the washer for 2 minutes.
For models with a timer control knob, turn the knob to any position other than the final spin for the interrupted cycle and then restore power.
For models with an electronic control knob or panel, select and start the wash cycle again after restoring power.
If the buttons do not work, try pressing the cancel button or pause button to reset the washer.
If frequent resetting is required, check the warranty or do a recall search.
If the washer is almost 10 years old and requires repairs costing $300 or more, it may be more cost-effective to replace it.
Key Points:
- Shut off circuit breaker or unplug washer for 2 minutes
- For timer control knob models, turn knob to any position other than final spin and restore power
- For electronic control knob or panel models, select and start wash cycle again after restoring power
- Press cancel or pause button if buttons do not work to reset washer
- Check warranty or do recall search if frequent resetting is required
- Consider replacing washer if it is almost 10 years old and repairs cost $300 or more
Did You Know?
1. The first GE washer was introduced in 1908 and was powered by a gasoline engine rather than electricity, as homes at that time did not have widespread access to electricity.
2. The GE washer’s “reset” button is actually a very helpful safety feature that allows the machine to clear any error codes or malfunctions and start fresh.
3. GE washers have a remarkable water-saving feature called “PreciseFill,” which calculates the needed water level based on the weight and volume of the load. This not only reduces water consumption but also saves energy.
4. To reset a GE washer, simply unplug the machine for about one minute, then plug it back in. This action will often solve minor issues and reset the control panel.
5. The GE washer’s reset option is not just limited to fixing issues; it can also be used strategically. For example, if you accidentally press the wrong cycle or make a mistake in the settings, pressing the reset button will allow you to start over without any consequences.
Reasons for Pause or Interruption in GE Washer Cycle
When using a GE washer, it is not uncommon to experience a pause or interruption in the wash cycle. Various factors can contribute to this, including power failure, the test mode during assembly at the factory, or stopping the cycle before it is complete. These interruptions can sometimes cause the electronic controls of the washer to lock up, preventing further operation until reset. It’s important to understand the causes of these interruptions to effectively troubleshoot and reset the washer.
Resetting the Electronic Controls of a GE Washer
Resetting the electronic controls of a GE washer is a relatively simple process that can be done easily at home. By following a few steps, you can effectively unlock the controls and get your washer back in working order.
Here are the steps to reset the electronic controls of a GE washer:
-
Shut off the circuit breaker or unplug the washer: This is an important first step to ensure safety and allow the electronic controls to reset. Leave the washer unplugged or the circuit breaker off for a period of two minutes.
-
Restore power to the washer: After the two-minute interval, plug the washer back in or switch on the circuit breaker.
Following these steps should help reset the electronic controls of your GE washer and resolve any temporary issues that may have caused the interruption.
- Remember to follow all safety precautions while working with electrical appliances.
“Safety first! Always shut off the circuit breaker or unplug the washer before attempting to reset the electronic controls.”
Resetting with Circuit Breaker or Unplugging
To reset a GE washer, there are two methods: using the circuit breaker or unplugging the washer. Here’s how:
-
Using the circuit breaker: First, locate the circuit breaker panel in your home. Find the breaker that controls the power to the washer and switch it to the “off” position. This will cut off the power supply to the washer. Leave the washer in this powered-off state for a full two minutes to ensure a complete reset of the electronic controls. Once the two minutes have passed, restore power to the washer by turning on the circuit breaker.
-
Unplugging the washer: If you can’t find the breaker panel, simply unplug the washer from the power source. Again, leave the washer unplugged for two minutes to perform a thorough reset of the electronic controls. After the two minutes, plug the washer back in to restore power.
Following these steps will effectively reset your GE washer.
Resetting Models with Timer Control Knob
To reset models of GE washers with a timer control knob, follow these steps:
-
Turn the knob to any position other than the final spin for the interrupted cycle.
-
Once the knob is correctly positioned, shut off the circuit breaker or unplug the washer for two minutes.
-
After two minutes, restore power to the washer.
By following these steps, the electronic controls of the washer will be effectively reset, allowing you to use it as desired.
Resetting Models with Electronic Control Knob or Panel
In the case of GE washers equipped with electronic control knobs or panels, the process of resetting is slightly different.
To reset the washer, follow these steps:
- Restore power: After a brief interruption, such as a power outage, shut off the circuit breaker or unplug the washer.
- Turn power back on: Once the power is restored, turn on the circuit breaker or plug the washer back in.
- Select and start wash cycle: Once power is restored, select the desired wash cycle and start the washer.
By following these steps, the electronic controls will reset and the washer will resume normal operation.
To summarize:
- Shut off the circuit breaker or unplug the washer.
- Restore power by turning on the circuit breaker or plugging the washer back in.
- Select and start the desired wash cycle.
Remember to always consult the user manual for specific instructions on resetting your GE washer.
Other Methods of Resetting GE Washer
If the aforementioned methods of resetting the GE washer do not work, there are a few additional techniques to try:
- First, pressing the cancel or pause button on the washer can sometimes trigger a reset. This method is worth trying before moving on to more advanced troubleshooting techniques.
- If the buttons on the washer do not respond or do not reset the washer, an electronic reset might be required. It is advisable to consult the user manual or contact a professional technician for assistance in such cases.
- If frequent resetting is required, it is recommended to check the warranty or do a recall search, as this may indicate a larger underlying issue.
- In some cases, it may be more cost-effective to replace the GE washer if it is nearly a decade old and requires repairs costing $300 or more.
Note: Proper maintenance and timely troubleshooting will ensure the longevity and efficiency of your GE washer for years to come.
Keep in mind that resetting a GE washer is a straightforward process that can easily be done at home. By understanding the reasons for pause or interruption and following the appropriate resetting procedures for each model, you can quickly resolve issues and restore the functionality of your washer. It is always recommended to consult the user manual or seek professional assistance if you encounter any difficulties during the resetting process.
Check this out:
Frequently Asked Questions
How can I reset my GE washing machine?
To reset your GE washing machine, you can begin by either shutting off the circuit breaker or fuse connected to the washer, or unplugging it for a duration of 2 minutes. If your model has a timer control knob, try turning it around and back to a different position apart from the final spin of the interrupted cycle. After performing these steps, restore power to the machine. This should successfully reset the electronic controls and get your washing machine ready for use again.
Is there a reset button on a GE washer?
Unlike some other washing machines, GE washers do not have a dedicated reset button. Instead, you can perform a manual reset by simply disconnecting the power source and then reconnecting it. This can be done by either unplugging the washer or flipping the power switch on and off. So, if you encounter any issues with your GE washer, remember that there is no specific reset button, but a manual reset can easily be carried out by disconnecting and reconnecting the power source.
How do I reset my washer after error code?
To reset your washer after an error code, you can try a simple power-cycle by turning off the machine at the powerpoint, waiting for a minute, and then turning it back on. If this doesn’t resolve the issue, you can attempt a Master Reset. This involves opening and closing the door of the washing machine six times within a span of 12 seconds. This reset typically resets all the onboard components and is a method frequently utilized by appliance technicians.
Why is my GE washer not starting?
If your GE washer is not starting, it’s important to first check the power cord. Ensure that it is securely plugged into a working outlet and free of any damage. Extension cords should be avoided as they may not be able to consistently transmit the necessary voltage, leading to power interruptions. By addressing these potential power issues, you can troubleshoot and resolve the problem with your GE washer not starting.