How to Reset Maytag Bravos Washer: Essential Troubleshooting Steps

Preparing For The Reset

Before resetting your Maytag Bravos Washer, follow these steps to ensure a successful recalibration:

1. Empty the drum: Make sure there are no clothes or items left inside the drum. This will prevent potential damage during the reset process.
2. Close the lid: Ensure that the lid of the washer is closed properly. This is a safety precaution to avoid accidents while the machine is resetting.
3. Put the washer in stand-by mode: Make sure the washing machine is turned on but not actively running any cycles. This will allow for the recalibration process to occur smoothly.
4. Double-check that the drum is empty.
5. Close the lid properly.
6. Put the washer in stand-by mode.

Remember, taking these steps will help ensure a successful recalibration of your Maytag Bravos Washer.

Initiating The Recalibration Process

To start the reset process, you’ll need to follow a series of knob rotations. Begin by turning the Cycle Selector knob counterclockwise or left once. This will set the stage for the reset process. Then, turn the knob clockwise or right three clicks.

After that, rotate the main knob counterclockwise or left one click, followed by a turn clockwise or right one click. Continue turning the knob in a clockwise or right direction until all lights start blinking, and the Rinse only option lights up. This indicates that you have successfully entered the recalibration mode.

To initiate the recalibration process, simply press the Start button. This will start the recalibration process, which will take some time to complete. It is important to be patient and allow the recalibration to finish before proceeding.

Entering Service Mode

Once the recalibration process is complete, it may be helpful to enter service mode to check for any error codes or issues with the machine.

To enter service mode, follow these steps:

1. Start by turning the main cycle selector knob clockwise and counterclockwise while observing the LED lights.
2. Rotate the knob until the “Wash,” “Rinse,” and “Done” LEDs turn on.

Once you are in service mode, you can check for any error codes that are displayed by the machine. It is important to take note of these error codes and research their meaning before attempting to clear them. Understanding the underlying issue will help you address the problem effectively.

Tips:

• Always consult the machine’s manual for specific instructions on entering service mode and error code troubleshooting.
• Take necessary safety precautions while working on the machine.
• If you are unsure about any step, seek professional assistance to avoid causing further damage.

Troubleshooting Power Issues

If you encounter power issues with your Maytag Bravos Washer, there are a few troubleshooting steps you can take.

1. Check the breaker: Ensure it has not tripped.
2. Verify the outlet and plug: Test them with another appliance to ensure they are functioning correctly.

If the washer still does not have power, it may be helpful to check the door sensor. Make sure the door is fully closed and latched before starting the wash cycle. If the door is not closed properly, the machine will not receive power.

• Check the breaker
• Verify outlet and plug
• Ensure door is fully closed and latched.

It is important to check these aspects to troubleshoot power issues with your Maytag Bravos Washer.

Addressing Spinning And Drainage Problems

If you’re facing spinning or drainage issues with your Maytag Bravos Washer, there are several steps you can take to address these problems.

Firstly, ensure that you are using the correct detergent for your machine. Using the wrong detergent can cause spinning issues.

Furthermore, avoid overloading the machine with too many clothes. Overloading can unbalance the drum and hinder proper spinning. To ensure balanced spinning, distribute clothing evenly around the drum and avoid washing bulky items on their own.

If the washer still has trouble spinning, check for any stuck items that may be causing a blockage. These items can prevent proper spinning and drainage. Additionally, clean the drain hose to remove any debris or built-up lint that may be affecting the machine’s performance.

Additional Steps For A Successful Reset

To ensure a successful reset of your Maytag Bravos Washer, follow these steps:

1. Check that the controls are not locked and are properly aligned before starting the washer. This is important as locked controls can prevent the machine from functioning properly.
2. If the washer does not reset after the initial steps, try performing a power cycle. To do this, turn off the power to the washer and press the Start/Pause button for 5 seconds. Wait for 5 minutes, then plug the washer back in or turn on the breaker.
3. If a power cycle doesn’t work, you can try an alternative reset procedure. Press “Stop” twice, then press “Power”. Select a wash cycle and wash option, and finally, press “Start”. This alternative reset procedure may help resolve any lingering issues.
4. It is important to regularly clean and maintain your washer to ensure optimal performance. Periodically clean the pump filter to remove any dirt buildup. Also, check the water pressure, screen filter, and water inlet valve if the washer takes longer than usual to fill with water.
5. After resetting the machine, perform a test wash to confirm if the reset was successful. If the reset doesn’t work initially, you can try again or perform a power cycle. However, if mechanical problems persist, it may be necessary to fix or replace faulty components before attempting another reset.

Remember, following these steps is crucial for troubleshooting and maintaining the performance of your Maytag Bravos Washer.

---

Check this out:

---

Frequently Asked Questions

How do I factory reset my Maytag washing machine?

One recommended method to factory reset a Maytag washing machine is through a power cycle. Begin by disconnecting the power supply by either unplugging the machine or switching off the breaker. Next, press and hold the Start/Pause button for approximately 5 seconds before waiting for 5 minutes. Finally, reconnect the power supply or switch the breaker back on, and turn on the machine to complete the reset process. Following these steps should effectively restore the machine to its factory settings.

How do I reset the motherboard on my Maytag washer?

To reset the motherboard on your Maytag washer, one method is to disconnect the washer from power for a brief period and then reconnect it. Another technique involves pressing the Pause/Cancel button twice and the power button once. Additionally, an alternative option is to open and close the lid six times within a span of twelve minutes. These methods aim to reset the motherboard and address any potential issues with the Maytag washer’s functionality.

1. What are the step-by-step instructions to reset a Maytag Bravos Washer to its factory settings?

To reset a Maytag Bravos Washer to its factory settings, follow these step-by-step instructions.

First, ensure that the washer is not running any cycles and is powered off. Then, press and hold the “Control Lock” button for three seconds until the “Control Locked” indicator light turns off. Next, press and hold the “Delay Start” button for three seconds until the “Delay Start” indicator light turns off. Finally, release both buttons, and the washer will be reset to its factory settings.

Remember that this process may vary slightly depending on the model of your Maytag Bravos Washer, so it’s recommended to consult the user manual for exact instructions.

2. Are there any common troubleshooting techniques to try before resetting a Maytag Bravos Washer, and if so, what are they?

Yes, there are a few common troubleshooting techniques to try before resorting to resetting a Maytag Bravos Washer. Firstly, you can check the power supply by verifying if the washer is properly plugged in and if there is power to the outlet. Next, ensure that the water supply is connected and turned on. Additionally, it is advisable to check for any clogs or obstructions in the drain hose and clean it if necessary. Lastly, you can attempt to resolve any minor issues by simply restarting the wash cycle or unplugging the machine for a few minutes and then plugging it back in. These troubleshooting techniques may resolve common problems and eliminate the need for a reset in certain cases.

If the aforementioned troubleshooting techniques do not resolve the issue with the Maytag Bravos Washer, a factory reset may be required. To perform a reset, you can disconnect the washer from the power source for about one minute, then plug it back in. This can help to refresh the machine’s settings and potentially resolve any software-related issues. It is important to note that performing a reset will erase any custom settings or preferences and revert the washer back to its default settings.

References: 1, 2, 3, 4